• find parts for :

• ATV / UTV / SXS
• Motorcycles
• Snowmobiles
• Watercraft
• Other

Store Home

• ATV / UTV / SXS
• Motorcycles
• Snowmobiles
• Watercraft
• Other

Kit Flywheel + Gasket Puller for Arctic Cat 400 Manuel 2003-2006 | OEM Repl.# 3430-054 / 3430-071 / 0802-037 / 3430-053   KEY FEATURES  

Brand new kit magneto flywheel + flywheel puller + gasket

Direct replacement to your original unit

All item pictures are accurate; if in doubt, do not hesitate to compare our item to your original part

Plug-and-play, direct fit, easy installation

All products are tested

DESCRIPTION  

PLEASE NOTE: This kit will ONLY FIT on manual transmission.

Brand new Magneto Flywheel, Flywheel Puller and Gasket

• All products are tested
• All item pictures are accurate; if in doubt, do not hesitate to compare our item to your original part

Vehicle models fitment  

Arctic Cat 400 Manual -- 2003-2008

OEM part replacement  

RM22434-R00

Specifications  

Flywheel

Dimensions:

Exterior Diameter: 143 mm Interior Diameter: 120 mm Interior Diameter Center Housing: 18 mm Exterior Diameter Center Housing: 42 mm Thickness (exterior): 12 mm Thickness (interior): 13 mm Flywheel Puller 50 mm x 1.5 Right hand Female

instructions  

Flywheel

Before attempting to start your vehicle, adjusting the air gap is necessary. Rotate the flywheel so the raised node is lined up with the pick up/pulser coil and adjust as close as possible but no less than 0.010".

Flywheel Puller

Tips on removing a power sport vehicle flywheel / rotor:

Flywheel Pullers are very versatile engine service tools and are a must in every toolbox. Our large selection of best selling rotor and flywheel pullers fit just about any motorcycle or ATV. Flywheel pullers are very simple to use, having only an outer body to hold the flywheel and a screw to push on the crankshaft. Some are even simpler, having only a bolt to thread into the flywheel. A taper holds the flywheel or rotor and the crankshaft together. The flywheel is secured to the shaft by applying torque to the fixing bolt.

Most of the time, removing a flywheel or rotor is painless. But sometimes corrosion, over-torquing the fixing bolt, or heat-cycling can give you a hard time removing the flywheel. We too often see mechanics use a larger breaker bar or air impact tools to ease the flywheel off. These two techniques will damage the flywheel, the flywheel puller, or the crank. Avoid using them if you want to keep it cheap.

We can give you two simple tips to break a stuck flywheel loose. But how do you know if it?s stuck? You simply have to set your torque wrench to 50 ft-lbs and try to ease the flywheel off. If the flywheel is not stuck, you should be able to remove it with even less torque than this. If it is stuck, don?t use more torque or you might break your wrench.

If 50 ft-lbs does not do the trick, go fetch something like a 12 or 16 oz ball peen hammer. Hit the end of the flywheel puller with a medium blow. Many times, the shock you create will successfully remove your flywheel. Be prepared to catch the flywheel since the shock of the hammer can make the flywheel jump off. Once again, getting into that situation will be pricey. And don?t forget your safety glasses.

The hammer is not a be-all, end-all solution. Sometimes, you will have to find something more powerful, and that?s where the propane torch comes in. As a last resort solution, the heat should expand the flywheel but not the crank, since it is too massive to expand as fast. That way, the flywheel will become looser and will come off easier. Remember: In order to not set fire to your garage, your vehicle or yourself, certain precautions are necessary prior to heating the flywheel:

• Clean any oil or flammable liquids off the flywheel;
• Make sure your work area is free of any flammable liquids and that you work in a well ventilated area;
• Make sure to remove the gas tank, and set it aside at a safe distance.

Make sure the flame of your torch is focused, and heat only the center of the flywheel. This is due to the fact that some flywheels use adhesive or other fixing compounds to locate the magnets in the rim that can be damaged by concentrated heat. Here again, the wheel might fall off the crank, so be prepared to catch it. And remember that you just heated it, so make sure you can catch it without burning yourself.

With these tips and techniques, you are now equipped to handle any stuck flywheel without throwing your flywheel puller at it; unless you have a habit of working with machines that have been in a lake for months!

Item Delivery  

Our multiple North American locations, from which we ship our products, allows us to deliver 99.7% of our orders within the specified time period. If your item is not available in our main Colorado facility, we still guarantee that your order will be delivered within the specified time period.

If your item is not delivered within this time period, we will offer you a 5.00$ discount on your order. This guarantee applies to shipments delivered in the 48 continental USA states, excluding PO boxes.

customer service AsK seller a question

duties & taxes

International Buyers: Import duties, taxes, and charges are not included in the item price or shipping cost. These charges are the buyer's responsibility.

More than 20 years of assisting mechanics around the world resolving the worst electrical problems made us know our stuff. When it comes to vehicle electrics, we definitively are the power in powersports.

Customer service

• Part request

About us

• About seller page
• Add seller to favorite

• Condition: New
• Brand: RMSTATOR
• Replaces OEM Part#: RM22434-R00

See More